Boiler Knowledge

When the hot water boiler always needs to make up water, what's wrong with the boiler?

Under normal circumstances, the hot water boiler only needs regular water replenishment. If the boiler frequently needs a large amount of water replenishment, it means that there is a problem inside the boiler, which needs to be discovered and solved in time. Zhengzhou Fangkuai Boiler Factory has summarized the following possible reasons when the boiler always needs to make up water for your reference.

Phenomenon: The display value of the pressure gauge drops frequently.
       The water pressure of a normal boiler must be greater than 0.8bar, and the water supplement period should be more than 3-6 months. The boiler is connected with the heat dissipation system in the room to form a heating system. The water pressure gauge on the boiler shows the pressure value of the entire heating system, so make-up water is to make up the entire heating system. Therefore, in most cases, the frequent replenishment of water is a possible problem in the heating system, not a boiler problem.

Reason 1: the newly commissioned heating system
       The newly commissioned heating system had a lot of air in the early stage, and the automatic exhaust valve of the system caused the pressure to drop, which required multiple water replenishment.

Reason 2: There is a leak in the heating system
       The joints of the exposed pipes or buried pipes of the heating system may be leaky and have little leakage. Since the boiler is in the heating state, the entire system is hot, so the leaked water evaporates quickly. It is difficult to spot the leaks with the naked eye.
       If there is a boiler pressure drop and the leak cannot be found, it is recommended to check whether the boiler is leaking.
       Inspection Method:
       Stop running the hot water boiler, close the heating supply and return water valve under the boiler (make sure the valve can be closed), disconnect the boiler from the system directly, fill the boiler to an integer value, and observe for a period of time to see if there are fluctuations in the water pressure gauge. This method can simply determine whether it is a boiler problem or a water leakage problem in the heating system pipeline behind the valve.

Reason 3: Failure of the expansion water tank in the boiler
       Failure of the expansion tank will cause the system pressure to exceed 3 bar when the hot water boiler is heating up, and the safety valve will be protected by water leakage. Please contact the after-sales team of the boiler manufacturer for replacement.

Reason 4: The water supply valve is not closed tightly
       If the water supply valve is not closed tightly and the pressure of the tap water pipe network is low, the system will lose pressure when using domestic hot water.
       Solution: If there is frequent water replenishment, you need to contact the after-sale boiler factory to check the heating system as soon as possible to avoid damage to the hot water boiler caused by long-term water replenishment.

2021-11-07 14:16:32

Compared with ordinary boilers, what are the advantages of CNC boilers?

Compared with ordinary boilers of manufacturers on the market, CNC boilers are more intelligent and easier to operate, which saves labor costs and makes people more comfortable to use. Compared with ordinary boilers, what are the advantages of CNC boilers? Zhengzhou Fangkuai Boiler Factory will answer for you.

Common points of ordinary boilers and numerical control boilers: the heating surface is called the boiler, the combustion chamber is called the furnace, and both have temperature, pressure and flow detection instrument probes. The difference is the control method and the method of executing the control instruction.

Ordinary boilers read the test instrument data manually and then use brain knowledge and experience to judge whether the terms of the technical specification and operating procedures deviate from it? The deviation direction is becoming bigger and smaller, becoming positive and negative? Then adjust the deviation manually.

The numerical control boiler adopts the program controller to automatically collect the test data of the process parameter probe and compare the memory setting data. After the comparison calculation, the electric or pneumatic actuators are used to operate such as automatic water filling, automatic coal filling and oil filling, and automatic air filling. Being unattended is the main advantage. Domestic gas-fired hot water boilers are all such things. After ignition and operation, you only need to set the hot water outlet temperature at about 50-60 degrees to maintain the room temperature above 20 degrees. Winter heating is not suitable.

2021-11-05 14:15:48

What advantages does the WNS boiler launched by Zhengzhou Fangkuai Boiler Factory have that other bo

WNS type boilers refer to horizontal, internal combustion, and room-fired boilers. At present, they are widely used in the entire boiler market. The WNS type boiler launched by Zhengzhou Fangkuai Boiler Factory has a very high praise rate among users and is deeply loved by users and friends. This is mainly related to the advantages of the boiler itself.

1. Advanced automatic steam boiler controller, full Chinese LCD screen, man-machine interface, users only need to set easily, the boiler can start and stop, load adjustment, automatic water supply and other automatic operations according to user requirements. The boiler has complete functions, complete protection, simple operation, safe and reliable, and has a self-diagnostic function. Once the boiler is running abnormally, the combustion will be automatically interrupted and an audible and visual alarm will be issued.

2. The boiler burner is supplied by a world-renowned manufacturer, which automatically burns and stops according to the instructions of the controller. The independent program controller has multiple safety protections, safe and stable performance, and low maintenance rate.

3. The vertical steam boiler adopts the lower burner mode, the two-pass structure, the fuel is fully burned, and the boiler runs stably; the spoiler is inserted in the flue pipe to slow down the exhaust rate, increase the heat exchange, and the boiler has high thermal efficiency and reduces the user's use cost.

4. The horizontal steam boiler is a shell type full wet back and three-pass pyrotechnic pipe structure. The flame burns in a large combustion chamber with slight positive pressure, fully extended, low combustion heat load, high combustion heat efficiency, and effectively reduces the exhaust gas temperature. , Energy saving and consumption reduction, economical use. The structure of the corrugated furnace bladder and the threaded smoke tube not only improves the heat absorption strength of the boiler, but also meets the needs of thermal expansion of the heat exchange surface, which is scientific and reasonable, and durable.

5. The boiler has a large space for the bladder, a large amount of steam stored, and a strong ability to adapt to load. A reasonably designed built-in steam-water separator device meets the requirements of users for higher-quality steam. The furnace body is provided with manholes, head holes, and hand holes, which are convenient for cleaning the inside of the furnace bladder, making maintenance and maintenance extremely convenient.

6. Boiler safety is equipped with multi-level interlocking protection: pressure switch protection (automatically shut down and alarm when the pressure is higher than the set pressure), low water level protection (the water level in the boiler body is below the warning water level, automatically cut off the power supply and alarm), safety valve protection (The boiler pressure exceeds the working pressure, automatically venting and reducing pressure), to ensure that the boiler is safe and safe under various working conditions.

7. The organically combined mechanical and electrical integration appearance, exquisite and novel, compact structure, less space, convenient for transportation and installation.

8. It adopts new heat insulation materials and high-quality white color steel plate packaging, light weight, good heat preservation performance, beautiful appearance, and not easy to rust.

2021-11-03 14:15:09

What is the main difference between water tube boiler and fire tube boiler?

Both water-tube boilers and fire-tube boilers are relatively common boiler models. The difference between the two makes their target user groups different. So how do you choose to use water-tube boilers or fire-tube boilers? What is the difference between these two types of boilers? Let Zhengzhou Fangkuai Boiler Factory tell you.

The difference between water tube boiler and fire tube boiler lies in the difference of the medium in the tube. The water inside the tube of the water tube boiler heats the water through the external flue gas convection/radiation heat exchange; the inside of the fire tube boiler tube is flue gas, which allows the flue gas to heat the medium outside the tube to achieve heat exchange.

Fire tube boilers have simple structure, large water and steam volumes, good adaptability to load changes, and lower water quality requirements than water tube boilers. They are mostly used in small-scale enterprise production processes and domestic heating. The heating surface of the water tube boiler is convenient to arrange and has good heat transfer performance. It is structurally used for large-capacity and high-parameter working conditions, and has high requirements for water quality and operating level.

The main difference between the two types of boilers is:
       (1) Water tube boiler has a wider range of pressure adaptation, breaking through the pressure limit and meeting the 2.5MPa upper steam supply requirements. The fire tube boiler is used under the pressure of 2.5 MPa by the material wall thickness and pressure limitation;
       (2) Fire tube boiler shell boilers are too large due to the current equipment and tooling restrictions of various boiler manufacturers. Fire tube boilers are difficult to manufacture, usually 35t/h down-pipe structure boilers to achieve large-scale boilers. 35t/h upper boilers usually adopt water-pipe structure;
       (3) Fire tube boilers have the characteristics of compact structure. At the same output, the appearance and equipment weight are lower than fire tube boilers. Water tube boilers have more space for superheaters because of their larger size. Therefore, water tube boilers occupies a relatively large boiler room.

2021-11-01 14:08:54

Tips and tricks summarized by Zhengzhou Fangkuai Boiler Factory to make gas-fired hot water boilers

Gas-fired hot water boilers often use natural gas as a fuel, and natural gas as one of the clean fuels is not only very environmentally friendly, but also greatly improves the operating efficiency of the boiler. But one drawback of natural gas is that it is more expensive. If the boiler can be operated more energy-efficiently, it will inevitably save natural gas, thereby reducing input costs. Zhengzhou Fangkuai Boiler Factory has summarized some tips and tricks for making gas-fired hot water boilers more energy-efficient for your reference and understanding.

1. Strengthen the insulation performance of the house
       Use gas hot water boilers for heating. Indoors usually use floor heating or radiators to dissipate heat. If the house is not well insulated, a large amount of indoor heat is lost to the outside through thermal convection, while a large amount of outdoor cold air flows into the room, and the gas boiler continues to heat it. , The gas consumption is naturally large. Installing double glazing on the windows can save 20% of energy. If thick curtains are added to the doors and windows, it can save 5% to 10% of energy; close all doors and windows before leaving the house, and draw all the curtains , Insulate the house.

2. Control the indoor temperature scientifically and reasonably
       To make the gas hot water boiler more energy-saving, the room temperature must be controlled scientifically. The ideal indoor temperature is 20°C during the day and 15°C to 17°C at night. Since the wall gas boiler is normally open in winter, the temperature does not have to be set high, it is comfortable. In principle, the outlet water temperature (or return water temperature) should be lower when it is warmer, and the outlet water temperature (return water temperature) when the weather is cold. Temperature) should be higher; when the weather is warm, the starting temperature difference should be larger, and when the weather is cold, the starting temperature difference should be smaller.

In the process of using a gas hot water boiler, the heating valve of an uninhabited room can be closed or lowered, which can save gas to a certain extent. If you are on a long-term business trip or have not lived in, the water in the gas boiler, floor heating or radiator should be drained cleanly. This will not only eliminate the use of gas, but also don't worry about the gas boiler or the end of the radiator being frozen.

2021-10-31 14:07:27

How to use natural gas boiler to save energy?

Compared with fuels such as coal and biomass, the calorific value of natural gas is 8500 kcal/m3, which is still relatively high. Therefore, the use of natural gas boilers is also more energy-efficient than other types of boilers. However, the price of natural gas is still a bit expensive at present. How can we use natural gas boilers correctly to help save energy? Zhengzhou Fangkuai Boiler Factory is here to answer you.

During the operation of a general natural gas boiler, the extra part becomes superheated steam during the burning process and is discharged with the flue gas, so the exhaust flue gas temperature can reach about 220 degrees, which is not conducive to energy saving, but also Not friendly to the environment. We can install a tubular waste heat recovery device at the flue gas outlet, and use the flue gas heat to heat and prepare to be pumped into the boiler, which can save more than 5% of natural gas. In this way, the boiler thermal efficiency can be increased from 88% to 92% to 98% to 102% based on the low calorific value.

1. Improve the conditions for airflow encounters
       The purpose of improving the communication conditions of the two air streams of gas and air in a gas boiler is to increase their contact area. The larger the contact area, the larger the reaction area, which intensifies the combustion. Specifically, the gas and air can be divided into multiple streams, so that the two air streams have a certain speed and meet each other; one air stream (usually gas) passes through and is submerged in the other air stream, and so on.

2. Strengthen mixing and disturbance
       The combustion of gaseous fuels in gas-fired boilers is a single-phase reaction. It is easier to ignite and burn than solid fuels, but its combustion speed and combustion perfection are closely related to the mixing of gas and air. The better the mixing, the more rapid and complete the combustion, and the shorter the flame. Therefore, as long as the stability of the flame is not destroyed, the airflow velocity in the airflow outlet or combustion chamber should be increased as much as possible, and even barriers with high resistance such as baffles should be installed at the entrance to allow it to hit and blast the flame to increase the disturbance of the airflow. , To strengthen the mixing.

3. Preheat gas and air
       Increasing the temperature of gas and air can strengthen the combustion reaction. Therefore, the waste heat of the exhaust smoke should be used to preheat the gas and air temperature, so as to increase the combustion temperature and flame propagation speed, so that the combustion process can be strengthened.

4. Rotating and circulating air flow
       Promoting the rotation of the airflow can enhance turbulence and mixing. At the same time, a recirculation zone will be formed in the center of the rotating airflow to guide a large amount of flue gas to recirculate and circulate, which not only strengthens the mixing, but also prolongs the flow route and residence time of the flue gas in the gas boiler and reduces the loss of incomplete combustion.

5. Recirculation of flue gas
       In order to increase the temperature of the combustion reaction zone of the gas boiler, a part of the high-temperature flue gas can be led to the combustion chamber to mix it with the unburned or burning combustible mixture to increase the combustion intensity. However, it should be noted that the amount of recirculated flue gas should not be too large, otherwise it will dilute the combustible mixing hook due to too much inert material, which will slow the combustion speed, even lack of oxygen and pyrolysis, resulting in incomplete combustion loss of the gas boiler.

2021-10-29 14:05:02

Compared with other boilers, what are the advantages of gas boilers?

There are many types of boilers on the market, such as oil-fired boilers, coal-fired boilers, biomass boilers, and gas-fired boilers. The advantages of gas-fired boilers in these types of boilers are extremely high, and sales are gradually increasing. So, compared with other boilers, what are the advantages of gas boilers? Zhengzhou Fangkuai Boiler Factory will answer for you.

First, gas-fired boilers do not require coal ash stacking land, saving land.

Second, save water for auxiliary production of boilers. Coal-fired boilers and gas-fired boilers use the same normal production water, but gas-fired boilers save auxiliary water used for dust removal and slag removal in coal-fired boilers.

Third, reduce staff. Gas-fired boilers have fewer auxiliary equipment than coal-fired boilers, require fewer staff, and bear much less wages and welfare costs.

Fourth, save electricity costs for boiler production. The gas boiler has less fuel delivery and other auxiliary equipment, low power, and short continuous operation time, so it consumes low power and saves costs.

Fifth, reduce labor intensity. Coal-fired boilers require high-intensity physical labor in the process of coal transportation and slag removal, while the labor intensity of gas-fired boiler workers is relatively small.

Sixth, the layout of the gas boiler room is flexible, the floor space is small, and the noise generated is low.

Seventh, improve the environment. Coal-fired boilers produce a large amount of smoke and dust during operation, which causes great pollution to the environment, while natural gas is a clean energy source, which greatly improves the environment.

Therefore, gas-fired boilers have more advantages than traditional coal-fired boilers. The use of gas-fired boilers is safe and convenient. It can also improve air quality and give you a fresh living space.

2021-10-27 14:03:58

Zhengzhou Fangkuai Boiler Factory shares the situation that oil and gas boilers need to be shut down

For oil-fired and gas-fired boilers, emergency shutdown refers to immediately stopping the supply of fuel and air to the boiler and quickly stopping its operation. And when the oil and gas boiler is in operation, what situations need to start the emergency shutdown when it encounters it? Zhengzhou Fangkuai Boiler Factory will answer for you.

When the water level is lower than the visible water level of the water level gauge or higher than the maximum allowable water level, that is, when the boiler is seriously short of water or is seriously full of water.

When the main water supply pipe, main steam pipe, and reheat steam pipe burst.

When the superheater tube bursts, or the water wall tube bursts, the water level of the steam drum cannot be maintained. When deflagration occurs in the furnace or flue, causing serious damage to the equipment, and when the furnace is extinguished.

When secondary combustion occurs in the flue at the tail of the boiler, the exhaust gas temperature suddenly rises abnormally.

When all suction, blower or rotary air preheater stops running. When the safety valve does not return to its seat after the action, the steam pressure drops, and the steam temperature changes to a degree not allowed by the steam turbine.

When the steam pressure exceeds the operating pressure of the safety valve and the safety valve does not operate, at the same time, the exhaust steam valve to the empty and the primary and secondary bypass cannot be opened.

When all water level gauges are damaged and all water level gauges lose their indication.

When other irresistible accidents that endanger the safety of people and equipment occur.

2021-10-25 14:03:35

The application of condensing technology can effectively improve the operating efficiency of oil and

Condensing technology is a new energy-saving and environmentally friendly technology, and it is the key to improving the efficiency of condensing oil and gas boilers. The principle of condensing technology is not complicated. A simple summary is to recover the heat energy in the flue gas by condensing the flue gas. Zhengzhou Fangkuai Boiler Factory will explain in detail the application of condensing technology to effectively improve the operating efficiency of oil-fired and gas-fired boilers.

The exhaust gas temperature of traditional boilers is generally around 160~250℃ or even higher, so that the water produced during fuel combustion (such as natural gas: CH4+2O2→CO2+2H2O) is in the superheated state of water vapor in the flue gas, and the smoke Gas is lost from the chimney. The thermal efficiency of traditional boilers can only reach 85%~91%. The condensing gas boiler reduces the exhaust gas temperature to 50~70℃, fully recovers the sensible heat in the flue gas and the condensation latent heat of water vapor, and the thermal efficiency can reach up to 109%.

The core of the condensation technology is to reduce the heat loss of fuel combustion and efficiently absorb the heat generated by the fuel. At the same time, due to the condensation of the flue gas, the harmful substances in the flue gas are collected into the condensed water, reducing acidic substances and other pollutants into the air. emission. More advanced condensing gas boilers use smokeless combustion technology, which reduces the emission of nitrogen oxides (NOx can cause acid rain and greenhouse effect) to beyond 35mg/kwh.

2021-10-23 13:59:38

How should we deal with common problems in the operation of oil and gas boilers?

Oil and gas boilers are highly intelligent. They don’t need a large number of firemen like traditional coal-fired boilers, but only need 1-2 firemen for regular inspections. But this does not mean that we can ignore the operation of the boiler. If there is a problem during the operation of the boiler, we must also know how to deal with it correctly.

1. Severe water shortage in the boiler will cause deformation and damage of the pressure components, and even explosion of the furnace tube. If the boiler is not handled properly, a boiler explosion may occur. The causes of boiler water shortage accidents are mostly related to the lax paralysis and misoperation of the operators, or to the blockage of the water level meter due to no flushing measures. When we find that the boiler is in a state of water shortage, water should be strictly prohibited, and emergency shutdown measures should be taken.

2. The characteristic of co-boosting of soda and water is that the water level of the water level gauge fluctuates violently, the boiler water bubbles, a large amount of water is contained in the steam, the temperature of the steam drops, and water shock occurs in the pipeline when it is severe. The main reasons for this situation are poor water quality, high salt content, or excessive increase in boiler load. When we discover that the oil and gas boilers have steam and water co-emission, we must strengthen water quality treatment and increase continuous sewage discharge.

3. If the boiler is operated with overpressure, it may cause deformation of the components and damage to the edges; in severe cases, it may cause an explosion accident. The main reason for the occurrence of boiler overpressure is that the furnace staff blindly increase the working pressure or leave the job without authorization. Sometimes the boiler overpressure can also be caused by the failure of the pressure gauge and the safety valve at the same time. Therefore, it is necessary to strengthen the responsibility system of the stover's position and the inspection of safety accessories.

4. When the furnace tube is blasted, there will be noticeable blasting sound and steam injection sound, and the water level and steam pressure will decrease obviously. When this situation is discovered, emergency shutdown measures must be taken. The general reason for this situation is that poor water quality causes the furnace tube to scale or corrode; water shortage and tube bursting may also cause each other; in addition, due to design defects, insufficient material strength and poor welding quality, they may all cause tube burst accidents.

2021-10-21 13:58:25

 5/40
 
 5/40